Connect: Check known issues and workarounds
This page lists known issues with FluentPet Connect. Each issue uses the same format, so you can quickly scan the list and recognize your problem. Fixed issues older than a year are under Resolved issues.
Base stops sending presses to the app after a Wi-Fi or internet interruption
Section titled “Base stops sending presses to the app after a Wi-Fi or internet interruption”- Status: Fix rolling out
- Date: 2026-10-14, updated 2026-11-12
Cause
A bug in Base firmware 1.1.0. A Base that is kept plugged into power can lose its connection to FluentPet after a Wi-Fi or internet interruption of a few minutes (for example a router restart) and then stays asleep instead of reconnecting. It wakes up again on its own after up to 12 hours.
Signs of this issue:
- The Base is plugged into power.
- Words still play through the Base when Buttons are pressed.
- The app shows the Base as offline or last seen hours ago.
- No new Button presses appear in the app.
Solution
- Press the Base Button once. The Base reconnects within a couple of minutes.
- If it is still offline after a few minutes, unplug the Base from power, wait about 10 seconds and plug it back in.
Presses made while the Base was offline then appear in the app with their original times.
If the Base still shows as offline or presses still do not appear after a few minutes, and your Wi-Fi network has internet access, check status.fluent.pet for a service outage.
You do not need a factory reset, to re-link Buttons or to reinstall the app. A factory reset also erases the presses stored on the Base.
Notes
- The issue can happen again after the next connection interruption until the fix reaches your Base.
- The fix is in Base firmware 1.1.1. Since 2026-11-12 the update is being sent to every plugged-in Base. A plugged-in Base installs it on its own within about a day; pressing the Base Button once makes it check for the update right away. After the update the Base reconnects by itself after an interruption.
- A Base used on battery can be affected by a different issue, see Base on battery stops syncing with the app.
- This is a different issue from Words do not play through Base when plugged in: here words still play, but presses do not reach the app.
Base on battery stops syncing with the app
Section titled “Base on battery stops syncing with the app”- Status: Fix rolling out
- Date: 2026-11-12
Cause
Two Base firmware bugs that affect a Base used on battery (charged now and then rather than left plugged in). In both cases the Base keeps working locally but stops its automatic check-in with FluentPet, so nothing reaches the app:
- After a Wi-Fi setup that was interrupted before it finished, the Base can stop its 12-hour automatic check-in.
- After repeated failed Wi-Fi connections (for example on a weak signal), the Base can stop trying to connect to your Wi-Fi network at all.
Signs of this issue:
- The Base is used on battery.
- Words still play through the Base when Buttons are pressed.
- The app shows the Base as last seen days or weeks ago.
- No new Button presses appear in the app.
Solution
- Plug the Base into power and leave it plugged in for at least 15 minutes. This wakes the Base and lets it reconnect and install the fix.
- If the Base still does not appear online after that, run Wi-Fi setup for the Base again from the app (Hardware, select the Base, Wi-Fi setup). You do not need to re-link Buttons.
Presses stored on the Base upload when it reconnects. The Base keeps a limited number of presses, so after an outage of many weeks the oldest presses can be lost.
Notes
- The fix is in Base firmware 1.1.1. Bases that still check in receive it automatically. A Base that has already stopped checking in cannot download the update until it is plugged in or set up again as described above.
- If the Base went dark because it stopped trying to connect to Wi-Fi, only running Wi-Fi setup again brings it back; plugging it in alone is not enough.
Connect Button battery drains faster when Base is off or out of range
Section titled “Connect Button battery drains faster when Base is off or out of range”- Status: Active
- Date: 2025-01-14
Cause
The battery in a Connect Button can drain faster if the Button is unused for long periods and the Base it is linked to is turned off, out of range or has an empty battery.
Solution
If you store your Connect system or do not use it for a long time (for example several months):
- Remove the batteries from the Buttons to prevent battery drain or leakage.
- Or use battery pull tabs to disconnect the batteries.
Words do not play through Base when plugged in
Section titled “Words do not play through Base when plugged in”- Status: Active
- Date: 2024-10
Cause
A Base firmware bug that affects audio playback when the Base is plugged into power.
Solution
Use the Base unplugged, on battery.
Fixed in Base firmware 1.1.0 and later. The update is rolling out to Bases automatically. Bases receive updates on their own while connected to Wi-Fi.
Notes
- This is a different issue from Base stops sending presses to the app after a Wi-Fi or internet interruption: there, words still play, but presses do not reach the app.
Wi-Fi networks not appearing during Base onboarding
Section titled “Wi-Fi networks not appearing during Base onboarding”- Status: Active
- Date: 2024-05-03
Cause
The Amazon Shopper Panel app uses a custom DNS or VPN configuration that prevents the phone from communicating with the Base while the phone is connected to the Base’s local network.
Solution
- Temporarily remove the Amazon Shopper Panel app during setup.
- Reinstall it after setup.
Notes
- Turning off ad verification in the Amazon Shopper Panel app may also resolve the issue.
- Check that no other custom DNS configuration is active on your phone.
Button press produces no sound
Section titled “Button press produces no sound”- Status: Active
- Date: 2023-08-13
Cause
Unknown.
Solution
- Check that the Button lights blue when pressed.
- Try re-linking the Button with the Base.
- Plug the Base into power and unplug it again.
- Press the Base Button once.
- Wait 3 seconds.
- Double-click the Base Button to cancel.
If the Button still plays no sound, contact FluentPet support from Settings > Contact support in the app, or at info@fluent.pet.
Base Button unresponsive and LED not lighting up
Section titled “Base Button unresponsive and LED not lighting up”- Status: Active
- Date: 2023-06-14
Cause
A Base firmware bug.
Solution
There are two possible fixes:
- Contact FluentPet support at info@fluent.pet to trigger a fix manually. This can take up to 12 hours.
- Let the Base battery drain completely, then recharge it.
Resolved issues
Section titled “Resolved issues”Show resolved issues
Base onboarding fails on iOS
Section titled “Base onboarding fails on iOS”- Status: Fixed
- Date: 2024-12-12
Cause
A bug in app version 0.4.40 for iOS caused setup failures. During setup the app could display “Connection failed” and “We failed to connect to your Base.”
Solution
Temporary workarounds were:
- Set up the Base using an Android device.
- Use a previous app version.
The issue was fixed in app version 0.4.41.
Duplicate notifications
Section titled “Duplicate notifications”- Status: Fixed
- Date: 2024-10
Cause
An app bug caused notifications to be delivered twice.
Solution
Resolved in a later app update.
Notifications not working on Android 14
Section titled “Notifications not working on Android 14”- Status: Fixed
- Date: 2024-09-16
Cause
Notifications failed on some Android 14 devices across several models, including:
- Pixel 7 Pro
- Pixel 7a
- Motorola Razr+ (2023)
The issue appeared to be specific to Android 14 and also affected notifications outside the FluentPet app.
Solution
Resolved in a later app update.
Base onboarding fails on Android during registration
Section titled “Base onboarding fails on Android during registration”- Status: Fixed
- Date: 2024-08-02
Cause
A race condition in the app caused two simultaneous requests to the Base. If one request was processed before the other, the Base failed to register with FluentPet servers.
Solution
Fixed in app version 0.4.37 and later. Before the fix, retrying setup usually resolved the issue.
Some app screens load very slowly
Section titled “Some app screens load very slowly”- Status: Fixed
- Date: 2024-01-05
Cause
A backend bug. Sorting buttons by Most used could take several seconds or minutes for accounts with thousands of button presses.
Solution
Fixed in a newer backend version. The temporary workaround was to change the sorting to A-Z, because the app remembers the sorting preference between sessions.
Button presses appear in the app after 1 to 3 days
Section titled “Button presses appear in the app after 1 to 3 days”- Status: Fixed
- Date: 2023-07-08
Cause
A Base firmware issue that affected event synchronization.
Solution
Resolved in a newer Base firmware update.
Button battery life shorter than expected (about 6 months)
Section titled “Button battery life shorter than expected (about 6 months)”- Status: Fixed
- Date: 2023-07-01
Cause
A Button firmware bug.
Solution
Update the Button firmware to the latest version.
Wrong sound plays when a Button is pressed
Section titled “Wrong sound plays when a Button is pressed”- Status: Fixed
- Date: 2023-06-01
Cause
About 2% of Bases were upgraded to an intermediate firmware version that contained a bug.
Solution
Perform a factory reset and re-link the Buttons.
Base freezes while re-linking a Button
Section titled “Base freezes while re-linking a Button”- Status: Fixed
- Date: 2023-05-21
Cause
A Button firmware update bug.
Solution
- Remove the battery from the last Button linked.
- Insert the battery again.
- Retry the linking process.